91麻豆免费观看视频,国产成人国产在线播放,可以免费看黄的网久久,奇米四色狠狠干大香蕉,成人精品一区二区激情,四虎精品永久免费视频,日韩美女淫语av在线,四虎永久免费在线视频,一本久久精品午夜福利,最新亚洲国产高清激情

  • <strike id="emw0i"><menu id="emw0i"></menu></strike>
    <kbd id="emw0i"></kbd>
    <samp id="emw0i"></samp>
  • <strike id="emw0i"><s id="emw0i"></s></strike>
  • <dfn id="emw0i"><td id="emw0i"></td></dfn>
    • <samp id="emw0i"></samp>
    • Welcome to Hashimoto Precision Metal (Shenzhen) Ltd

      Mailbox:

      info@hskcoltd.com

      Hashimoto Precision Metal (Shenzhen) Ltd

      Specialize in precision stamping parts since 1935
      News
      Your position: Home > News > Industry news > How to detect the short-circuit fault of automotive wiring terminal?

      Contact us

      Hashimoto Precision Metal (Shenzhen) Ltd

      Address: No. 25, Xinfa East Road, Xiangshan Community, Xinqiao street, Bao'an District, Shenzhen 518125, P.R.China

      Tel: +86-755-27267875

      Email: info@hskcoltd.com

      Industry news

      How to detect the short-circuit fault of automotive wiring terminal?
      Release time:2022-06-03Views:4420


      A short circuit between the harness and the body (ground) or the relevant switches may also cause wire and terminal failures. Before inspection,
      check whether the body terminal is firmly fixed, and then test according to the following steps.

      1. Check the connection and disconnection of wires
      First, remove the terminals on both sides of the control computer ECU and the sensor, and then measure the resistance between the corresponding terminals. If the resistance value does not exceed 1 ohm, then the wire is normal for the next inspection. To improve the accuracy of measurement, it is better to gently shake the wire both vertically and horizontally. Also, pay attention to most wire terminals. The multimeter rod shall be inserted from the rear end of the connector, but the waterproof terminal rod with waterproof sleeve shall not be inserted from the rear end, because the terminal rod will be deformed if not careful.

      2. Check the short-circuit resistance value
      First, remove the wire terminals on both sides of the control computer ECU and the sensor, and then measure the resistance between both sides of the connector terminals and the body. If the resistance is more than 1 ohm, one end of the rod shall be measured on both wire connectors.

      3. Check the terminal appearance and contact pressure
      First, remove each terminal one by one, check whether there is rust contact and dirt on the connector terminal, and remove corrosion and dirt. Then check whether the terminal strip is loose or damaged and whether the terminal is firmly fixed. The terminal shall not be loose when pulling gently. On the contrary, if the plug terminal is easier to pull out than other seat holes, it may cause poor contact during use.

      Inquire Now * required
      Submit
      成人久久精品国产亚洲av| 亚洲自拍偷拍视频大全亚洲| 日本人妻vs中文字幕| 黄色一区二区三区蜜桃| 蜜桃噜噜一区二区三区| 久久一区二区三区六区| 国产精品亚欧美一区二区| 国产一级高清片在线观看| 精品氩 99久久久久久黄无码| 日本美女精品免费一线| 91亚洲国产成人精品性色| 国产老妇伦国产熟女老妇高清| 亚洲国产精品久久久久久| 日韩精品无码中文字幕一区二区| 国产精品美女黄色av| 国产老妇女牲交视频| 内射一区二区在线播放| 亚洲一区二区三区电影网站| 国产精品97久久久久久久| 国产精品看高不产品不卡| 亚洲碰碰人人av熟女天堂| 国产日韩欧美一二三级| 内射人妻日韩内射人妻| 碰超免费人妻中文字幕| 最新av不卡在线免费观看| 欧美日韩中文亚洲三区| 性做久久久久久久久| 日韩一区二区二区在线| 黄色片视频网站入口| 天天操天天射夜夜撸| 古玲一区二区三区视频| 日韩视频在线一区二区三区| 国产精品呻吟一区二区三区| 久久国产精品高清一区二区三区| 激情亚洲一区二区三区| 久久国产精品二国产人妻| av在线不卡一区二区三区| 日本精品在线亚洲国产欧美| 日本视频一区二区三区视频| 亚洲人妻在线一区二区三区| 色久悠悠视频在线观看|